MANUAL
Alpha® Pneumatic
Air Polisher
Instruction Manual
Part No: AIR-658
For repair information call:
Headquarters, Oakland, NJ — (800) 648-7229
Factory Service and Training Center, Las Vegas, NV — (888) 292-5742
Due to specially designed components this machine must be serviced only
with genuine ALPHA® parts.
103 Bauer Drive, Oakland, NJ 07436 • 800-648-7229 • Fax: 800-286-0114
INTRODUCTION
Thank you for purchasing anAlpha®Air Polisher. This polisher is the workhorse of
a complete polishing system. A wide range of accessories help you perform many
different tasks. This tool lets you grind, shape, bevel, contour and polish all kinds
of granite and marble. You can easily change from one type of disc to another
in just a matter of seconds. The tool is used with water to help you get the best
possible finish, to reduce the health risks of dust, and to give the most savings
in time and money from modern accessories. For your safety, please read this
manual thoroughly before you start operating this polisher.
ABOUT THE SYMBOLS
According to the hazard level, all safety notes in this manual are classified into
“DANGER”, “WARNING”, and “CAUTION”.
DANGER!
Death or serious personal injury is imminent when handling
this polisher incorrectly.
WARNING! There is a possibility of death or serious personal injury when
handling this polisher incorrectly.
CAUTION!
There is a possibility of personal injury or property damage
when handling this polisher incorrectly.
Note: In some situations, failing to observe WARNING notes could result in
death or serious personal injury. Be sure to read and observe the safety
notes to ensure safety and correct use of the polisher.
ELECTRICAL SYMBOLS
The following show the symbols used for tool.
V
Volts
A
Hz
Amperes
Hertz
3
~ or a.c.
n0
Alternating Current
No load speed
…/min
kg
Revolution or reciprocation per minute
Kilograms
Protective Earth
SAFETY INSTRUCTIONS FOR POWER TOOLS
1. KNOW YOUR POWER TOOL. Read owner’s manual carefully. Learn its
applications and limitations as well as specific potential hazards particular
to this tool.
2. KEEP WORK AREA CLEAN. Cluttered areas and benches invite
accidents.
3. AVOID DANGEROUS ENVIRONMENTS. Keep work areas as dry as
possible. Do not use tool in presence of flammable liquids or gases. Keep
the area well lit.
4. KEEP CHILDREN AND VISITORS AWAY. All visitors should be kept a safe
distance from the work area. Keep out of reach of children.
5. DON’T FORCE TOOL. It will do the job better and safer at the rate for
which it was designed.
6. WEAR PROPER APPAREL. Do not wear loose clothing or jewelry as it can
get caught in moving parts. Rubber gloves and insulated non-skid footwear
are recommended. Wear protective covering to contain long hair.
7. WEAR PROPER EYE PROTECTION. Use safety glasses at all times. Also,
use a face mask if work area is dusty.
8. WEAR PROPER EAR PROTECTION. Wear ear protectors when using
for extended periods.
9. DON’T ABUSE WATER SUPPLY HOSE. Don’t carry tool by supply hose
or expose to traffic areas where it can be crushed.
4
10. ALWAYS SECURE WORK PIECE. Use clamps or a vise to hold work. It’s
safer than using your hand and it frees both hands to operate tool.
11. DON’T OVERREACH. Keep proper footing and balance at all times.
12. DISCONNECT TOOLS WHEN NOT IN USE. Always disconnect tool before
servicing; when changing accessories such as grinding wheels, backer
pads, etc.
13. REMOVE ADJUSTING KEYS AND WRENCHES. Form a habit of checking
to see that keys and adjusting wrenches are removed from tool before
turning it on.
14. MAINTAIN TOOLS WITH CARE. Keep tools clean at all times for best
and safest performance. Follow instructions for lubricating and changing
accessories. Keep handles dry, clean and free of oil or grease. Inspect
moving parts for alignment and binding as well as for breakage and improper
mounting.
15. AVOID ACCIDENTAL STARTING. Don’t carry a “connected” tool, or make
adjustments, or change discs without making sure the air valve is in the off
position to prevent the flow of air.
16. USE ONLY RECOMMENDED ACCESSORIES. The use of any accessories
other than what is listed or recommended for this particular tool may be
hazardous.
17. KEEP HANDS AWAY FROM ALL MOVING PARTS.
18. USE SIDE HANDLES. Supplied with tool for control and safety.
19. USE RECOMMENDED GRINDING WHEELS ONLY. Do not use
conventional abrasive grinding wheels with this tool. Only use diamond
grinding wheels which are rated for wet usage.
20. STAY ALERT. Watch what you are doing and use common sense. Do
not operate tool when you are tired, or under the influence of medication
or alcohol.
5
RECOMMENDED ALPHA® ACCESSORIES
Ceramica EX flexible diamond polishing discs, waterproof Sandpaper discs, Hook
and Loop Backed Felt Wheels, Core Drill Bits, Twistouch Turbo and Profilers.
SPECIAL FEATURE
TheAlpha® Air Polisher was designed with human engineering for operator comfort.
It comes equipped with a silencer which reduces the level of noise as well as
guiding the cold exhaust air away from an operator during the polishing process.
This feature also eliminates excess lubricant dripping on the work piece. Portions
of the body design are made with synthetic materials and covered with rubber to
prevent fatigue and coldness to hands.
SPECIFICATIONS
Air
Air
Pressure
Air
Inlet
Water
Inlet
RPM
Weight
Spindle
Consumption
2.64 lb
1.2 kg
15 CFM
87 PSI
U.S.
No Load 3,500
1/4” BSPP
1/8” BSPP
5/8”-11
420 ℓ/ Min
0.6Mpa (6 bar)
METRIC
ACCESSORIES
Splash / Safety guard.........................................................1pc
Water hose (10 ft / 3m).......................................................1pc
Air hose (10 ft / 3m)............................................................1pc
Wrench (22mm) .................................................................1pc
Side handle ........................................................................1pc
Silencer / Muffler ...............................................................1pc
Lubrication Oil (1oz / 30 cc sample bottle)...............................1pc
C-Shape Handle.................................................................1pc
6
MODEL AIR-658 PART NAMES
Adjustable Water Valve
Rubber Body cover
Internal Water Line
Adjustable Air Valve
10 ft Air Hose
Reversible Handle
10 ft Water Hose
Rubber Splash Guard
TOOL SET-UP INFORMATION
Unpack the tool carefully and study the helpful hints and warnings contained in
this manual. Please take time to familiarize yourself with the features of the tool.
Be sure to fill out the registration card enclosed, and mail it back to the distribution
center today.
AIR FITTINGS AND PRESSURE
Your new Alpha® polisher is designed for continuous duty polishing. When select-
ing your compressor, buy a system
which can handle a constant flow
of air. We recommend that you
purchase a heavy duty two stage
cast iron type unit. The system
should include a regulator and a
moisture trap.
7
•
•
Each tool requires: 87 PSI (0.6Mpa / 6 bars); however the range of 85-90 PSI
is acceptable.
(6 kg / cm2) of air pressure and 15 CFM (420 l / min.) of air flow.
We suggest a minimum of 5 HP air compressor with a holding tank of 50
cubic feet (1,400 l) capacity for one tool.
•
•
Air hose fitting is 1/4” BSPP
The use of heavy duty 3/8” (10mm) hose is suggested for all lines.
LUBRICATION (Lube Oil is used to protect the tool from rusting when not in use)
PROPER CAREAND LUBRICATIONARE IMPORTANT FACTORS IN THE USEFUL
LIFE OF THIS TOOL.
At the end of each workday, 2-3 drops of lubricant oil, solvent free oil (included with
each polisher) should be placed in the air inlet at the base of the tool. Rotate the
spindle counter clockwise, by hand 3-4 revolutions. Reinstall the air hose and run
the tool for a minute or two. (Replacement containers of oil may be purchased from
Alpha Professional Tools® Part # AIR-008.)
Maintenance and Usage Tip
Automatic oilers are not recommended: the volume, grade, and composition of oil
used may cause premature failure. In-line air dryers are recommended to extend
the life of the tool. Old or worn compressors, which emit oil through the air lines,
can dramatically shorten the life of the tool.
SPINDLE SIZE
The Alpha® AIR-658 air polisher features a 5/8”-11 size spindle. This tool has
been designed for portable/shop production and uses all modern accessories.
It is very important that you do not run anything heavier than the recommended
accessories on this machine. A drop of oil should be applied to the outside
threads whenever attachments are changed to facilitate removal and prevent
rust. A 22mm Spindle Wrench is provided to assist in changing accessories.
Maintenance and Usage Tip
• Do not leave the tool submersed in water. This could expose the inner
moving parts to moisture, which will shorten the life of the tool.
• Do not leave threaded accessories (backer pads, core drill bits, profilers) on
the spindle of tool for extended periods of time; this may result in making it
difficult to remove these accessories.
• Excessive force or impact to the spindle may result in premature failure of
gears and/or bearings, which may not be immediately evident.
8
AIR VALVE LEVER
The valve lever controls the flow of air through the tool.
It has two positions- ON or OFF. Run the tool at the
recommended range of 85-90 PSI, with the lever pointing
to the ON position. This will produce 3,500 RPM. Do not
try to vary the speed. The tool works best at full throttle
only. Do not attempt to exceed the recommended speed
by excess pressure.
WATER CONTROL VALVE
This valve lets you adjust the flow of water through the spindle. It may be used to
shut off the water entirely when changing discs. When storing the tool overnight,
open the valve and drain all water from the supply hose and tool.
SILENCER / MUFFLER
To comply with OSHA Occupational Noise Exposure Standard Number 1926.52,
this polisher is equipped with a Silencer. When the polisher is operated correctly
at 87 PSI, the sound level emitted should be 80 dBA. The Silencer is also used
to maintain a constant back pressure inside the tool; this helps to prevent it from
exceeding the recommended 3,500 RPM.
The exhaust hose for this tool also helps to reduce the noise level by venting the
exhaust air and residual air-line, thus eliminating the risk of excess lubricant drip-
ping on the work piece.
Silencers should be replaced when dirty or clogged to provide optimum performance.
A spare silencer is included with the purchase of a new polisher.
Maintenance and Usage Tip:
• Operating the tool at a pressure that exceeds the recommended operating
specifications or without the silencer may result in premature failure of the
tool.
• The silencer, Part # 658-52, should be replaced when it no longer allows air
to flow freely. This is indicated by a dark, shiny appearance.
WARNING!
Tools sent in for repair, where the silencer is removed or blown out,
are not covered under our Limited Warranty!
9
SPLASH / SAFETY GUARD
For operator comfort and safety, a splash guard has been provided. The guard
should remain in place for all grinding and polishing operations.
C-SHAPE HANDLE / REVERSIBLE SIDE HANDLE
The C-Shape handle: During use with Alpha® Core Bits and Alpha® Profilers,
use of the “C-Shape” handle is recommended. C-Shape handle will allow
operator to have more control and ease of operation during these applications.
Reversible Side Handle: Attach the handle into the threaded socket on either
the left or right side of the tool. A locknut is slipped onto the threads to keep the
handle safely in position.
Maintenance and Usage Tips:
Do not apply more force or pressure than the force created by the weight of the
polisher itself. The polishing discs are designed to work properly under lightweight
pressure. Applying excessive force or pressure may damage the disc and could
shorten the life of the tool.
WATER SUPPLY HOSE
This hose may be connected to any garden hose using a clamp. The hose is com-
posed of a special material to avoid kinks. Replacements are available should the
hose become damaged, Part # 133229.
10
ACCESSORIES AND FACTORY SERVICE
All the accessories can be purchased at a local distributor in your area.
For more information concerning Alpha® Air Polisher and factory service,
please contact the Alpha® distribution centers listed below.
COMPANY HEADQUARTERS:
Alpha Professional Tools®
103 Bauer Drive
Oakland, NJ 07436
8:30 a.m. – 5:00 p.m. EST
201-337-3343
Hours of Operation:
Telephone Number:
Toll-Free Number:
800-648-7229
FACTORY SERVICE AND
TRAINING CENTER:
3625 W. Teco Ave.,
Suite #5
Las Vegas, NV 89118
7:30 a.m. – 4:00 p.m. PST
702-837-9515
Hours of Operation:
Telephone Number:
Toll-Free Number:
888-292-5742
Limited Warranty of Alpha® Air Polisher (AIR-658)
Alpha Professional Tools® warrants this product against defects in material and
workmanship for a period of 90 days from the date of original retail purchase
(proof of purchase required). If Alpha Professional Tools® receives notice of such
defects during the warranty period, our obligation assumed under this warranty is
limited to the repair or replacement of parts, without charge. This warranty does
not apply to tool accessories.
For Warranty Claims: Send complete tool with all your information and details
of the problem to the Alpha Professional Tools®, transportation prepaid. Do not
send tool accessories.
11
ALPHA® PNEUMATIC AIR POLISHER SCHEMATIC
86
12
ALPHA® PNEUMATIC AIR POLISHER PARTS LIST
DRAWING NO.
PART NO.
658-01
658-02
516-44
AWP-21A
658-09
658-10
658-11
658-12
658-13
658-14
516-20
658-16
658-17
516-48
516-49
516-50
658-21
658-22
658-23
658-24
658-25
516-18
658-28
658-29
658-30
658-31
658-32
516-25
516-26
516-27
516-28
658-37
658-38
658-43
658-45
658-46
DESCRIPTION
Screw M4x10
Pipe-joint Assembly
Oil Seal
C-shape Handle, 2 Bolts, 2 Washers
W-pipe
Head Packing
Body
Body Cover
Spring Washer M10
Grip
Bearing 608 ZZ
Snap Ring
Spiral Bevel Gear
Bearing 6302 ZZ
Oil Seal
QUANTTY
1
2
3
4
9
2
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
28
29
30
31
32
33
34
35
36
37
38
43
45
46
44 Nut
Gear Shaft 5/8”-11 Thread
Half Moon Key
O-ring
5/8 Nozzle
Spiral Bevel Pinion
Bearing 6001 ZZ
F-bearing Case
Rotor Spacer
Cylinder (Includes Part No. 658-31)
Spring Pin
Rotor
Vane (4 Piece Set)
R-bearing Case
Bearing 626 ZZ
Bearing Cap
Air Inlet Case
Body Packing
Screw M4x10
Wave Washer
M-14-nut
13
ALPHA® PNEUMATIC AIR POLISHER PARTS LIST
DRAWING NO.
PART NO.
658-47
658-50
658-51
658-52
516-53
658-54
133229
AWP-56
AWP-57
AWP-74
658-59
AWP-75
658-61
658-62
658-63
658-64
658-65
658-66
658-67
658-68
658-69
DESCRIPTION
O-Ring
Valve Lever
Hex Socket Head Screw
Silencer
Liner
QUANTITY
47
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
2
1
4
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
Nipple
Water Hose 8mm OD x10ft (3m)
Compression Ring
Compression Nut
Hose Coupling
Clamp
Gasket 24x14x3
Splash Guard
Wrench 22mm
Needle Valve
O-ring
R-ring
M8 Nut
05 Washer
A-valve (Includes Part No. 658-69)
Needle Pin
Endcase w/O-ring and Bushing Only
(Includes Part No. 658-72 & 658-73)
70
658-70
1
71
72
73
74
78
79
80
81
82
84
85
86
—
516-79-2
658-72
658-73
658-74
658-78
516-79-1
658-80
658-81
658-82
658-84
Air-hose Joint 1/4” BSPP
O-ring
07 Bushing
Exhaust Hose (Leather)
Complete Endcase Assembly
Air-hose
Shim.01mm
Shim.03mm
Shim.05mm
Shim.01mm
1
1
1
1
1
1
1
1
1
1
1
1
1
658-85
Oval Key
Lubrication Oil (1oz / 30 cc)
Air Polisher Lube Oil (8 oz)
Sample bottle
AIR-008
14
PRODUCT REGISTRATION CARD
Model No.
Serial No.
Company Name: ______________________________________________
Name: ______________________________________________________
Address: ____________________________________________________
City: _______________________State: ________Zip: ________________
Telephone: ___________________________________________________
Purchase Date: _______________________________________________
Dealer’s Name: _________________________________
Note: Serial & Model Number must be included for proper registration.
(800) 648-7229
Mail or Fax to:
Alpha Professional Tools
®
103 Bauer Drive, Oakland, NJ 07436
Fax: 800-286-0114
Photocopy of product registration form will be accepted.
15
15
103 Bauer Drive, Oakland, NJ 07436 • 800-648-7229 • Fax: 800-286-0114
Copyright © 2005 Alpha Professional Tools. All rights reserved.
5/21/08
|